Voron Serial Request Guide — How to Get Your Voron Serial Number

社区 指南 新手

获取Voron序列号是每位装机者的必经仪式。这是社区验证您自行组装打印机并达到正版Voron质量标准的方式。审批通过后，您的Voron将获得唯一标识符（如V2.4-001、V0.2-042）并加入官方序列列表，同时解锁专属社区频道、认证交易论坛及Voron社区的完全认可。

本指南将详解所有要点：序列号的定义、要求、装机文档规范、申请提交方法、审核重点及一次通过审批的技巧。

什么是Voron序列号？

Voron序列号是社区颁发的认证标识，证明您的打印机为自行组装的真实Voron。它不仅是装饰标签，更是您机器符合社区质量、安全与性能标准的凭证。

• 组装证明： You must demonstrate that you physically assembled the printer yourself from a kit or self-sourced parts. Pre-built printers or printers purchased already assembled are not eligible.
• 质量门槛： The serial request process ensures that serialized Vorons meet minimum quality standards — safe wiring, proper cable management, functional motion system, and good print quality.
• 社区成员资格： Once serialized, you get the "Voron Owner" role on Discord, access to the serial-owner-only channels, and the ability to participate in verified trades.
• 永久记录： Your serial number is permanently listed in the Voron Serial Registry, a public database of every serialized Voron ever built.

要求

提交序列号申请前，请确保您的装机满足以下所有要求：

• 必须是自组装的 Voron： You must have assembled the printer yourself. Kits are fine (Formbot, LDO, FYSETC, or self-sourced). Pre-built printers from any source are not eligible.
• 必须是标准 Voron 设计： The printer must be one of the official Voron designs (V2.4, Trident, V0.2, Switchwire, Legacy, V1.8). Heavily modified printers may be rejected — keep the design recognizable as a Voron.
• 必须功能正常： The printer must be fully assembled, wired, and capable of printing. It doesn't need to be perfectly tuned, but it must move, heat, and extrude.
• 必须有文档记录： You need to provide photos and optionally a video demonstrating the printer and its print quality.
• 必须在 Discord 中发帖： Serial requests are submitted through the Voron Discord server in the #serial-request channel. No other submission method is accepted.

所需文档

照片（必需）

您需提交至少三张照片（可包含5-6张）。每张照片中必须清晰显示手写Discord用户名及纸张。

• 照片 1 — 前 3/4 视角： Shows the toolhead, gantry, and overall printer structure. This is the most important photo. It should clearly show the toolhead, XY gantry, belt path, and enclosure panels. Good lighting is essential.
• 照片 2 — 电子舱： Shows your wiring, mainboard, power supply, and electronics layout. The reviewers will check for safe wire gauges, proper strain relief, no loose connections, and general tidiness.
• 照片 3 — 包含用户名的整机照片： A wider shot showing the full printer with your Discord username placard clearly visible. This confirms the printer is yours and is in your possession.

视频（强烈推荐）

打印质量演示视频非强制要求，但能显著提高审批通过率。若无视频，审核员可能要求补充后再批准。

• 第一层测试： Show a first layer being laid down — a single-layer square or a bed-level test pattern. The lines should be evenly squished with no gaps, no scratching, and consistent adhesion across the bed.
• XYZ 立方体： Print a 20mm XYZ calibration cube at standard speed (80-100 mm/s). Show the final result on camera — sharp corners, flat top surface, no visible layer shifts or ringing.
• 复杂打印件： A Voron part (like an AB drive cover or a toolhead component) or a Benchy demonstrates that the printer can handle overhangs, bridges, and detail work without artifacts.

视频提示： Use good lighting. Keep the camera steady (a phone tripod helps). Record at 1080p or higher. The video can be uploaded to YouTube, Streamable, Imgur, or Discord's native video upload.

如何提交序列号申请

步骤1：加入Voron Discord

If you haven't already, join the Voron Discord server atdiscord.gg/voron. You'll need to read and accept the rules in the #welcome channel before you can access other channels.

步骤2：阅读置顶消息

Navigate to the#serial-request channel and read the pinned messages. These contain the current submission format, any temporary rule changes, and tips from the moderation team. The format is updated occasionally, so always check the pins, even if you've read an older guide.

步骤3：准备您的帖子

序列号申请帖的标准格式为：

**Printer Type:** Voron V2.4 350mm
**Kit/Frame Source:** Formbot Kit
**Mainboard:** BTT Octopus Pro 1.1
**Toolhead:** Stealthburner + Clockwork 2
**Hotend:** Dragon UHF
**Firmware:** Klipper (Mainsail)

[Photos attached]
[Video link if applicable]

Include your photos as Discord attachments. If you have a video, include a link (YouTube or Streamable preferred). If using Discord's native video upload, make sure it's compressed correctly — large files may fail to upload.

步骤4：发帖并等待

发帖后请耐心等待。审核时间从几小时到几天不等，取决于版主空闲情况。请勿@版主、多次发帖或直接私信版主询问审核进度。您的请求会被审核。

审批技巧

以下是序列号审核员关注的因素。逐一满足这些条件，您几乎肯定能在首次提交时通过。

• 整洁的布线： Use cable ties or cable sleeves to bundle wires neatly. Avoid tangled wiring looms. Run wires along the extrusion channels where possible. Use proper-length cables — not too long (excess coil) and not too tight (strain on connectors).
• 无松散线缆： Every cable should be secured. Dragon chain cables (on the V2.4) should be properly tensioned. Electronics bay wires should be routed cleanly — no cables dangling over the mainboard, no unsecured AC power wires.
• 面板安装到位： For enclosed printers (V2.4, Trident, V0.2), the enclosure panels should be installed. A printer with panels off looks unfinished.
• 框架方正可见： The photos should show that the frame is square — corners should align properly, no visible gaps at joints, no twisted extrusions.
• 线缆管理规范： Use cable chains (if applicable) properly. Wire bundles inside chains should be organized — power separate from signal where possible. No cables rubbing against sharp edges.
• 电子元件整洁： The mainboard compartment should be tidy. Label your connections if possible. Use ferrules on screw terminals (required for safety). Ensure AC wiring has proper strain relief and is routed away from low-voltage signal wires.
• 照明良好： Take photos in a well-lit area. Use natural daylight or a work light. Avoid backlit shots where the printer is in shadow. The reviewer needs to see details.
• 打印质量优秀： Your first layer test should show consistent squish across the entire bed. Your XYZ cube should have sharp corners with no ringing. No stringing, no blobs, no layer shifts.

常见拒绝原因

以下是序列号请求被拒绝的最常见原因及如何避免：

• 照片质量差： Blurry, dark, out of focus, or distant shots where details can't be seen. Retake with better lighting and a steady hand.
• 布线杂乱： Tangled cables, loose wires hanging in the electronics bay, no cable management at all. This is the single most common rejection reason.
• 未展示打印质量： Photos of the printer alone without any demonstration of printing capability. Always include at least a first layer test and preferably a completed print.
• 缺少零件： Printer assembled without panels, missing extruder, missing hotend fan, unplugged cables. The printer should be fully assembled and functional.
• 未显示用户名： The handwritten Discord username must be clearly readable in at least one photo. Use a bold marker on white paper.
• 预组装或购买的打印机： Serial reviewers can often identify pre-built printers — clean but without the telltale signs of a self-build (minor alignment adjustments, unique cable routing choices, custom modifications). Don't try to pass off a pre-built as self-built.
• 非标准改装： If your printer heavily deviates from the standard Voron design (custom frame size, non-standard motion system, radically different electronics layout), you may need to explain your build in detail or it may be rejected.

审批通过后的流程

一旦您的序列号请求获批，将发生以下事项：

• 已分配序列号： Your printer gets a unique serial number based on the model and the order of approval (e.g., V2.4-4231, V0.2-1985). This number is yours permanently.
• 序列列表条目： Your Voron is added to the official Voron Serial Registry at serials.voron.dev. The entry includes your Discord username, printer model, and serial number.
• Discord 角色： You receive the "Voron Owner" role on the Voron Discord, giving you access to the serial-owner channels.
• 序列所有者频道： These exclusive channels include discussion areas for advanced mods, verified trading and selling of Voron parts, and a community of experienced builders who have also passed the serial process.
• 已验证交易： The serial-owner channels have a dedicated trading section where you can buy and sell Voron parts with other verified owners. This is much safer than the open market — there's accountability and a reputation system.
• 社区认可： Your Discord nickname is typically updated to include your serial number, and you gain credibility in discussions about Voron builds and tuning.

拥有序列号的好处

除了完成组装并获得社区认可的满足感外，序列号还提供实际好处：

• 交易验证： When buying or selling Voron parts in the community, having a serial number proves you're a legitimate builder, not a scammer. Many sellers in the serial-owner channels require a serial number before they'll do business with you.
• 版主权限： Some community-developed mods are only shared in the serial-owner channels or require a serial number to access the download links.
• 优先支持： While help channels are open to everyone, serial-owners often get more detailed troubleshooting help because the reviewers know the builder invested the effort to build correctly.
• 炫耀特权： Low serial numbers (e.g., V2.4-0001 to V2.4-1000) carry prestige in the community as early-adopter indicators.

总结

序列号请求流程看似繁琐，但设计初衷是让任何花时间正确组装打印机的制作者都能完成。要求很直接——组装一台整洁的打印机、拍摄好照片、展示打印质量、并以正确格式提交。审核员都是经验丰富的制作者，他们希望看到您成功。如果请求被拒绝，请仔细阅读反馈，修复问题后重新提交。大多数拒绝在第二次尝试时都能解决。

获得序列号是您 Voron 组装之旅的最后一步，也是融入完整 Voron 社区的第一步。这值得付出努力。祝您好运，打印愉快。